The last generation has been a total mess for both Intel and AMD.
AMD had motherboards frying CPUs, crazy stupid post issues due to DDR5 memory training (and my personal build fails to post like 25% of the time due to this exact same stupid shit), and just generally less than a totally reliable experience compared to previous gens.
Intel has much the same set of problems on their 13/14th gen stuff: dead chips, memory training issues, instability.
Wonder if it’s just a fluke that both x86 vendors are having a shitty generation at the same time, or if something else is at play.
Memory training:
https://www.crucial.com/support/articles-faq-memory/ddr5-memory-trainingleave the system powered to complete this process, which in some instances has been seen to take up to 15 minutes.
Have you tried this?
If you don’t let it finish, the system will continue to POST with unstable values.
My biggest complaint is that there should be a visual indication of this process. Many users are utterly unaware it is going on.
During this process the system firmware is configuring itself for the newly installed memory. LEDs on the motherboard or computer may or may not be active during this process. On-screen symptoms of this may be a black screen or the system pausing on a manufacturer splash screen.
If this is happening, just leave the system powered to complete this process, which in some instances has been seen to take up to 15 minutes. If this is successful the system will either begin operating normally after the elapsed time, or may require a reboot but will work normally once this is done.
The UX for this seems to be absolute shit. The system seems to hang, and give no indication of something going on? And in the end, the system may need a reboot to complete the process? It better give some indication when it’s complete then, or else.
The UX for this seems to be absolute shit.
Absolutely, this is decidedly user hostile design.
Not to mention hearing about it through word of mouth… Just 🤦♂️
It’s just the easiest way to do this. Memory training is a very early step in the boot process. Firmware only has the CPU cache available as memory and most hardware in the system isn’t initialized yet. Most of this isn’t even done by the UEFI firmware itself, but by calling a binary blob provided by the CPU manufacturer, for intel it is called FSP and AMD i believe it is AGESA. I’d have to check, but I believe at the point memory training is running the PCIe bus has not even been brought up and scanned, so video output in this phase would require extensive reengineering of the early boot process from both the CPU manufacturer, firmware vendors and the board manufacturer. PCIe has DMA so making that work without memory might be a challenge. There are three easy to implement solutions though: post codes if your mainboard has a display for them, serial output if the board has a serial port (though this needs another device to read the messages) and the cheapest solution could be a flashing LED on the board labeled memory training in progress.
Flashing LED would be great IMO. And a HUGE improvement.
Holy crap. Never heard of this. Thanks!
Maybe x86/x64 has reached the end of its development lifecycle, and both companies are at the point where they simply can’t squeeze any more out of it, so every trick they try results in these abnormalities?
I dunno.
Because they are pushing their chips even harder. AMD literally pegs them at the maximum temperature these days. It’s basically factory overclocking for both companies. Of course it’s going to run into issues, voltage + temperature fries chips
Factory overclocking is a marketing term. Overclocking means running a processor above its specified speed, but if it intentionally ships that way from the factory it is by definition operating within specification.
To be fair I joined a couple of months after the release but I have 0 of these issues. Maybe time to update your BIOS?
In regards to the memory training: have you double-checked how much Ram your CPU actually supports, at what frequencies? For example even the 7950X3D supports only DDR5-3600 when you put more than 2 bars of ram in, leading to issues with memory training taking long/not posting/instability if you enable any form of overclocking in that scenario. I had that problem before and switching from 4 bars to two fixed everything. Just in case this might be your issue as well.
Intel problem is that they keep pushing extensions race while AMD proved with their Ryzen series that if you keep your instruction set to a minimum, then your CPUs will be energy efficient, even arm proved this by pushing extensions too far like intel and getting overheating chips
Both intel and AMD are running the same instruction set though are they not? (Cross licensing x86/x64)
Look up gcc x86 options https://gcc.gnu.org/onlinedocs/gcc/x86-Options.html , intel have twice as big instruction set, and with expansion of instructions of arm, risc architecture ain’t saving it from overheating now because of aforementioned, now bloated instruction set
This isn’t true anymore, Intel dropped AVX512 since they moved to Big+Small cores design while AMD actually implemented it with Zen 4.
